ICND2 | 200-105 Interconnecting Cisco Networking Devices Part 2

TestPrep Academy

Exam: 200-105

Question: 1 / 55

90:00

What is used in an SDN deployment to provide communication between the controller and the various network devices?

A. Cisco APIC-EM

B. Simple Network Management Protocol

C. Northbound APIs

D. Southbound APIs

Which two statements are true with respect to OSPF or BGP? (Choose two.)

A. BGP is the only official EGP used by the Internet

B. OSPF is a classful routing protocol

C. BGP is the only IGP used for routing

D. OSPF performs intra-AS routing

E. Both protocols perform inter-AS routing

Two bridges share the lowest bridge priorities on a network. Which metric is used to break the tie, when electing a root bridge?

A. Lowest MAC Address

B. Number of links between switches

C. Number of ports on the switch

D. Highest MAC Address

E. Bridge ID

Which is a layer of an SDN solution that is responsible for forwarding traffic?

A. Management Plane

B. Application Plane

C. Control Plane

D. Data Plane

You are configuring a PPP link between two devices using a serial connection. Your organization's security policy requires PAP authentication to be used when the remote device does not support CHAP. Which command should you use to authenticate incoming PPP sessions?

A. Router(config)#ppp authentication pap chap

B. Router(config)#ppp authentication chap pap

C. Router(config-if)#ppp authentication pap chap

D. Router(config-if)#ppp authentication chap pap

You are implementing interVLAN routing using a Router-on-a-Stick configuration. Which command is used to associate 802.1Q tagged traffic from VLAN 3 with a subinterface?

A. Router(config)#encapsulation 802.1q 3

B. Router(config)#encapsulation dot1q 3

C. Router(config-if)#encapsulation 802.1q 3

D. Router(config-subif)#encapsulation dot1q 3

What is the main purpose of enabling DHCP snooping on a company’s network?

A. Intercept all ARP requests and all replies on the untrusted ports

B. Implement identity-based networking based on the client-server access control

C. Prevent rogue DHCP servers

D. Restrict a port to a specific set of MAC addresses

In what configuration mode would you set the HSRP version using the standby version command?

A. User EXEC Mode

B. Privileged EXEC mode

C. Global configuration mode

D. Interface configuration mode

Which commands create an EIGRP routing process in IPv6 for AS 200 on router R2?

A. R2(config)#

ipv6 router eigrp 200

R2(config-rtr)#

no shutdown

R2(config-rtr)#exit

B. R1(config)#

interface Ethernet0/0

R1(config-if)#

ipv6 eigrp 200

R1(config-if)#exit

C. R2(config)#

ipv6 unicast-routing eigrp 200

R2(config-rtr)#exit

D. R2(config)#

interface Ethernet0/0

R2(config-if)#

ipv6 eigrp 200

R2(config-if)#exit

E. R1(config)#

ipv6 router eigrp 200

R1(config-rtr)#

no shutdown

R1(config-rtr)#exit

Which routing protocol represents a link-state routing protocol?

A. BGP

B. IGP

C. EIGRP

D. OSPF

E. RIP

Which is an open source southbound API for SDN networks that is used to define flow path through the network?

A. OpenFlow

B. onePK

C. OSPF

D. NETCONF

E. SNMP

Refer to the |h %5coutput%5ct10%5cmisc%5c200105eo316.html exhibit.

Which two statements are true if eBGP peering is used? (Choose two.)

A. A single homed design is implemented.

B. The AS numbers for the ISP and remote router must match.

C. The IGP routing protocol for the ISP and remote router must match.

D. The two routers form a TCP connection with one another.

E. A dual homed design is implemented.

Which two routing protocols depend on directly connected neighbors for their view of the network? (Choose two.)

A. BGP

B. EIGRP

C. RIPv2

D. OSPF

Which two statements regarding the OSPF router ID are true? (Choose two.)

A. The router ID will change if the interface the router is using for the router ID goes down.

B. A configured loopback interface overrides the OSPF router ID.

C. Using the router-id command is the preferred procedure to set the router ID.

D. The router ID is used to identify the OSPF process running on the router and it is of local significance only.

Which technology is typically used for provider-managed VPNs?

A. IPsec

B. MPLS

C. DMVPN

D. GRE over IPsec

Refer to the |h %5coutput%5ct6%5cmisc%5c200105eo225.html command output. Which statement is true concerning the details in the output?

A. Routing will not occur due to mismatched areas.

B. The equal costs will introduce a routing loop.

C. The router is configured as an ABR.

D. LSAs will be processed on every router.

What is the maximum number of switches that can be connected together using StackWise?

A. 5

B. 12

C. 6

D. 9

QoS can use different types of mechanisms for classification and marking. Which of the following fields is used to indicate Layer 3 IPv4 packets?

A. TID

B. TOS

C. COS

D. DSCP

Which protocol is used for exchanging routes between two different autonomous systems?

A. RIPv2

B. EBGP

C. OSPF

D. EIGRP

Which of the following is considered a trusted device in terms of QoS? (Choose two)

A. Switches

B. PCs

C. Printers

D. Routers

Which type of ACL has a usable range of 100-199 and can be matched to a source or destination on an individual port basis?

A. Outbound ACL

B. Standard ACL

C. Extended ACL

D. Inbound ACL

Which of the following describes Data traffic with regards to QoS concepts?

A. Drop-sensitive

B. Bursty

C. UDP priority

D. Smooth

E. TCP retransmits

F. Delay-sensitive

Review the following configuration:

Switch(config-if)#

switchport mode trunk

Switch(config-if)#

switchport trunk native vlan 99

Switch(config-if)#

switchport trunk allowed vlan 2,3,99

Which VLAN will pass untagged traffic?

A. VLAN 2

B. VLAN 99

C. VLAN 1

D. VLAN 3

Which three steps are required for a basic BGP configuration between a customer network and an ISP? (Choose three.)

A. Advertise the networks into BGP

B. Define the BGP process.

C. Establish one or more neighbor relationships.

D. Configure an appropriate IGP between the ISP and customer

E. Set the AS number of the customer network to match the ISP

Which command would be used if you would like to see the contents of all ACLs on your Cisco router?

A. R1#show ip access-list

B. R1#show ip interface brief

C. R1#show ip interface

D. R1#show access-lists

Which two WAN connectivity methods allow you to create a broadband connection using PPPoE? (Choose two.)

A. PSTN

B. Ethernet

C. DSL

D. ATM

E. Cable

You unbox a new Cisco switch that has not been configured. By default, which VLAN will be used by connected devices and for management purposes?

A. 99

B. 1

C. 999

D. 10

You need to monitor basic end-to-end WAN connectivity between HQ and the branch office. You want to test end-to-end connectivity every 15 seconds and if connectivity is not successful you need to be notified. What should you do?

A. Issue the traceroute command on the HQ router with a destination of the Branch router.

B. Implement an SNMP NMS and configure Branch as an SNMP agent.

C. Create an IP SLA ICMP Echo test from the HQ router to the Branch router.

D. Issue the ping command on the HQ router with a destination of the Branch router.

When configuring PPPOE, which command ties the dialer interface configuration to a physical interface?

A. interface |i interface-id

B. ip address negotiated

C. dialer pool |i number

D. pppoe-client dial-pool-number |i number

Refer to the |h %5coutput%5ct10%5cmisc%5c200105eo318.jpg exhibit BGP has been preconfigured on the ISP side.

Which command starts the BGP process on R1?

A. network 10.0.1.0

B. neighbor 192.168.1.10 remote-as 1

C. neighbor 192.168.1.10 remote-as 100

D. router bgp 100

E. router bgp 1

F. network 10.0.1.0 mask 255.255.255.0

What does configuring BPDU guard on a switch help prevent?

A. Unauthorized access to the network by rogue computers

B. Console access to the switch

C. A rogue switch being plugged in to the network

D. Network loops

Which command would you use to verify that the dialer interface is up for a PPOE client?

A. show ip interface brief

B. show ip protocols

C. show pppoe session

D. show ip statistics

You have configured the following on your Cisco IOS switch:

SW1(config)#

monitor session 11 source interface fastethernet 0/2 both

SW1(config)#

monitor session 11 destination interface fastethernet 0/0

Which statements are true about the configuration?

A. SW1 will filter frames based on the entries in ACL 11.

B. All received and sent frames on fastethernet 0/2 will be redirected to fastethernet 0/0.

C. All received and sent frames from devices on fastethernet 0/2 matching ACL 11 will be copied to fastethernet 0/0.

D. Interface fastethernet 0/0 will only allow monitored traffic to pass through it.

E. All received and sent frames on fastethernet 0/2 will be copied to fastethernet 0/0.

Which are two reasons for implementing an external AAA server such as RADIUS or TACACS+ for authentication? (Choose two.)

A. Centralized administration

B. Smaller databases

C. Decentralized administration

D. Scalability

You only want VLAN 10, 15, and 20 to traverse the trunk between two switches. Which command should you use?

A. SW#switchport trunk allowed vlan 10,15,30

B. SW(config)#switchport trunk allowed vlan 10,15,30

C. SW(config-if)#switchport trunk allowed vlan 10,15,30

D. SW(config-vlan)#switchport trunk allowed vlan 10,15,30

Refer to the following commands:

R1(config)#

ip access-list standard Subnet_ONLY

R1(config-std-nacl)#

permit 10.1.1.0 0.0.0.255

What is being configured in this example?

A. Inbound ACL

B. Named ACL

C. Standard ACL

D. Extended ACL

Which is an external AAA option that is Cisco proprietary?

A. RADIUS

B. Active Directory

C. TACACS+

D. LDAP

Which type of site-to-site VPN provides zero-touch configuration for new spokes?

A. DMVPN

B. GRE over IPsec

C. IPsec Tunnel

D. IPsec VTI

Which protocol is an example of an EGP?

A. IS-IS

B. IGRP

C. EIGRP

D. BGP

Which command will allow you to display the entire BGP table?

A. show ip bgp summary

B. show ip bgp neighbors

C. show ip bgp all

D. show ip bgp

If congestion occurs on an interfaces configured to use QoS, which congestion management tool is activated only when there is congestion?

A. Weighted fair

B. Scheduling

C. Queuing

D. Strict priority

Refer to the |h %5coutput%5ct6%5cmisc%5c200105eo229.html partial command output for the show ip eigrp topology command. Which two routes are feasible successors? (Choose two.)

A. via 10.2.2.2 (6026496/2172416), Serial0/3/0

B. via 10.3.3.1 (5729792/2169856), Serial0/0/0

C. via 10.2.2.2 (6023936/2169856), Serial0/3/0

D. via 10.3.3.1 (5220352/28160), Serial0/0/0

Which layer of the SDN architecture is responsible for controlling all of the physical and virtual devices in the network?

A. Application plane

B. Data plane

C. Control plane

D. Management plane

You are configuring inter-VLAN routing using a multilayer switch. Which command is used to create the SVI for vlan 20?

A. vlan 20

B. network 20.0.0.0

C. encapsulation dot1q 20

D. interface vlan 20

Which four statements describe the most pertinent features and functions of SNMP? (Choose four.)

A. SNMPv2 provides improved performance and manager-to-manager communications as compared to SNMPv1.

B. SNMP can make use of management agents that reside on managed devices such as NMS and MIB agents.

C. SNMPv3 provides secure access to devices by a combination of authenticating and encrypting packets over the network.

D. SNMP traps are sent by management agents to the network management system when certain events occur.

E. SNMP defines how management information is exchanged between endpoint devices.

F. There are five basic SNMP messages that the network manager uses to transfer data from agents that reside on managed devices.

You need to ensure that an OSPF router ID will not change. Which two tasks will accomplish this goal? (Choose two.)

A. Use a loopback address as the router ID.

B. Use dual stack integration.

C. Set the router ID manually.

D. Set the hello and dead intervals to match.

When managing a large corporate network, which technology allows you to centrally manage VLANS?

A. STP

B. MSTP

C. VTP

D. DTP

Which SNMPv3 level of security requires authentication only?

A. authPriv

B. Community strings

C. noAuthNoPriv

D. authNoPriv

Which command can be used to verify what VLANs are permitted to travel across a trunk between two switches?

A. show protocols

B. show interfaces switchport

C. show interfaces trunk

D. switchport mode trunk

You are implementing an SDN solution. What is the function of the controller?

A. It is a business application that monitors the network.

B. It is a router responsible for forwarding packets to other local area networks.

C. It is a switch responsible for forwarding frames within a local area network.

D. It is a centralized device the controls all of networking devices.

Which command can you use to verify the values that are being used in the EIGRP metric composition?

A. show interface

B. show ip route eigrp

C. show ip eigrp neighbors

D. show ip eigrp topology

Which two fields is the OSPF hello packet contain information that must be agreed upon by both routers before an adjacency can form? (Choose two.)

A. Router ID

B. Area ID

C. Neighbors

D. Router priority

E. Hello/dead interval

Which type of cloud services provides only networking services?

A. MBaaS

B. PaaS

C. IaaS

D. SaaS

Which protocol allows you to create EtherChannels in a multivendor environment?

A. PAgP

B. SPAN

C. LACP

D. MISTP

Refer to the |h %5coutput%5ct6%5cmisc%5c200105eo231.html exhibit. EIGRP has been configured with all default settings. You enter the following command:

R1(config-router)#

variance 2

Which paths will be load balanced?

A. 1 and 2

B. 1 and 3

C. 1, 2, and 3

D. 2 and 3

While calculating your results take a moment to complete our simple survey!

How likely is it that you would recommend TestPrep.Academy to a friend or colleague?

0 - Not at all likely

10 - Extremely likely